Planter with bench AMRUM ø1,9 m with thermo-ash
Product number:
UW-120-03-82-D1900
These are packing dimensions
Is produced for you, delivery time 21-28 Tage
Product information "Planter with bench AMRUM ø1,9 m with thermo-ash"
Mobile planter TYPE AMRUM with integrated bench
Material of planter:
Quality S355J2W + N,
Material no. 1.8965
Visible sides optically pre-rusted
Dimensions of planter:
Round with all-round bevelling at top 60 mm and 20 mm, for high stability and round edges
Diameter: ø1.900 mm
Height: 500 mm
Height of bench: 475 mm
Height of planter: 25 mm higher than bench
One bench oval cut with 2x radius R950 mm
Total width approx. 1,350 mm
Material of seat cover:
High-quality thermo-ash 25x118 mm (wood quality with seal of quality), very high weather resistance, dark stained suitable for outdoor use. Wooden supports screwed from below.
The seat supports are screwed from below with a stainless steel crossbar so that no fastening screws are visible from above. The complete pre-assembled seat support is then screwed onto the bench substructure with screws between the seat supports. All screws are of high quality stainless steel A2
Delivery includes base, water-permeable
Incl. 4 pieces of lugs for crane transport of the plant troughs and/or for fastening shrubs. The straps are welded into the corners approx. 100 mm below the top edge. Drill hole for hooks: ø40 mm.
Foundation: on site
Corten steel in stainless steel look will show some rust peeling of 0.05 mm of the surface, especially in the first few years. We therefore recommend planning the installation in such a way that this rust detachment can run off in a defined manner and no discolouration occurs in the area of the objects.
When combining wooden seat supports and Corten steel, the iron oxide adhering to the surface and the tannic acid present in the wood can cause dark grey and black discolouration of the wooden supports. This is a natural process in this combination and does not justify a complaint. With increasing natural greying of the wood, the grey stains that appear in advance disappear and the surface colour converges.
The seat cushions are made of wood. Wood is a natural material that can vary in colour. The seat covers are made exclusively from kiln-dried wood. Despite all care, drying cracks may occur and knots may be visible. These are natural characteristics and do not justify a complaint. Border samples can be matched on request.
Wood care instructions:
All wood used outdoors turns grey within a few months and takes on the typical silvery appearance. It is possible to oil the wood with suitable wood preservative oil so that the greying of the wood is delayed. You can find more information on this on our homepage at www.gartenmetall.de
Material of planter:
Quality S355J2W + N,
Material no. 1.8965
Visible sides optically pre-rusted
Dimensions of planter:
Round with all-round bevelling at top 60 mm and 20 mm, for high stability and round edges
Diameter: ø1.900 mm
Height: 500 mm
Height of bench: 475 mm
Height of planter: 25 mm higher than bench
One bench oval cut with 2x radius R950 mm
Total width approx. 1,350 mm
Material of seat cover:
High-quality thermo-ash 25x118 mm (wood quality with seal of quality), very high weather resistance, dark stained suitable for outdoor use. Wooden supports screwed from below.
The seat supports are screwed from below with a stainless steel crossbar so that no fastening screws are visible from above. The complete pre-assembled seat support is then screwed onto the bench substructure with screws between the seat supports. All screws are of high quality stainless steel A2
Delivery includes base, water-permeable
Incl. 4 pieces of lugs for crane transport of the plant troughs and/or for fastening shrubs. The straps are welded into the corners approx. 100 mm below the top edge. Drill hole for hooks: ø40 mm.
Foundation: on site
Corten steel in stainless steel look will show some rust peeling of 0.05 mm of the surface, especially in the first few years. We therefore recommend planning the installation in such a way that this rust detachment can run off in a defined manner and no discolouration occurs in the area of the objects.
When combining wooden seat supports and Corten steel, the iron oxide adhering to the surface and the tannic acid present in the wood can cause dark grey and black discolouration of the wooden supports. This is a natural process in this combination and does not justify a complaint. With increasing natural greying of the wood, the grey stains that appear in advance disappear and the surface colour converges.
The seat cushions are made of wood. Wood is a natural material that can vary in colour. The seat covers are made exclusively from kiln-dried wood. Despite all care, drying cracks may occur and knots may be visible. These are natural characteristics and do not justify a complaint. Border samples can be matched on request.
Wood care instructions:
All wood used outdoors turns grey within a few months and takes on the typical silvery appearance. It is possible to oil the wood with suitable wood preservative oil so that the greying of the wood is delayed. You can find more information on this on our homepage at www.gartenmetall.de
detail.tabsContentTitle
| Format: | Ø1900 |
|---|---|
| Material: | Corten steel |
| Seat cushions: | Thermo ash H25xW120mm |
Login