Planter with bench BORKUM 3.0 m x 1.5 m
Product number:
UW-181L-03-72-3000-1500
Is produced for you, delivery time 28-35 Tage
Packing dimensions:
x x mm | 310 kg
Product information "Planter with bench BORKUM 3.0 m x 1.5 m"
Mobile planter
with integrated bench on the long side
Material of planter:
Grade S355J2W + N
Material no. 1.8965
Visible sides optically pre-rusted
Dimensions of planter:
Rectangular with all-round bevelling at top 60 mm and 20 mm, for high stability and round edges
Length: 2,980 mm
Width: 1.480 mm
Height of planter: 500 mm
Height of bench: 475 mm
Height of planter: 25 mm higher than bench
Length of bench: 2,980 mm
Seat depth: 490 mm
Incl. 4 straps for transport and/or fastening wood
The straps are welded into the corners approx. 100 mm below the top edge. Hole for hooks for hanging: ø40 mm.
Material seat support:
100% hardwood with quality seal
Edges chamfered
Surface planed
Dimensions bench:
Seat support lengthwise
Type SAQ 6x65x65
Seat bar cross-section 65x65 mm
Spacing approx. 20 mm
The seat supports are screwed from below with a cross lath made of stainless steel so that no fastening screws are visible in the wood from above. The complete pre-assembled seat support is then screwed onto the bench substructure with screws between the seat supports. All screws are of high-quality A2 stainless steel.
Without side rests
To protect the roots from frost and heat damage, we recommend lining the walls with at least 20 mm of insulation made of PUR insulation boards.
Delivery includes base, water-permeable
With corten steel in a stainless steel look, a certain amount of rust detachment of 0.05 mm of the surface occurs, especially in the first few years. We therefore recommend that you plan the installation in such a way that this rust separation can run off in a defined manner and that there is no discolouration in the area of the objects.
When combining wooden and corten steel seat covers, the iron oxide adhering to the surface and the tannic acid present in the wood can cause dark grey and black discolouration of the wooden covers. This is a natural process in this combination and does not justify a complaint. With increasing natural greying of the wood, the grey stains that appear in advance disappear and the surface colour converges.
The seat cushions are made of wood. Wood is a natural material that can vary in colour. The seat covers are made exclusively from kiln-dried wood. Despite all care, drying cracks may occur and knots may be visible. These are natural characteristics and do not justify a complaint. Border samples can be matched on request.
Wood care instructions:
All wood used outdoors turns grey within a few months and takes on the typical silvery appearance. It is possible to oil the wood with suitable wood preservative oil so that the greying of the wood is delayed. You can find more information on this on our homepage at www.gartenmetall.de
with integrated bench on the long side
Material of planter:
Grade S355J2W + N
Material no. 1.8965
Visible sides optically pre-rusted
Dimensions of planter:
Rectangular with all-round bevelling at top 60 mm and 20 mm, for high stability and round edges
Length: 2,980 mm
Width: 1.480 mm
Height of planter: 500 mm
Height of bench: 475 mm
Height of planter: 25 mm higher than bench
Length of bench: 2,980 mm
Seat depth: 490 mm
Incl. 4 straps for transport and/or fastening wood
The straps are welded into the corners approx. 100 mm below the top edge. Hole for hooks for hanging: ø40 mm.
Material seat support:
100% hardwood with quality seal
Edges chamfered
Surface planed
Dimensions bench:
Seat support lengthwise
Type SAQ 6x65x65
Seat bar cross-section 65x65 mm
Spacing approx. 20 mm
The seat supports are screwed from below with a cross lath made of stainless steel so that no fastening screws are visible in the wood from above. The complete pre-assembled seat support is then screwed onto the bench substructure with screws between the seat supports. All screws are of high-quality A2 stainless steel.
Without side rests
To protect the roots from frost and heat damage, we recommend lining the walls with at least 20 mm of insulation made of PUR insulation boards.
Delivery includes base, water-permeable
With corten steel in a stainless steel look, a certain amount of rust detachment of 0.05 mm of the surface occurs, especially in the first few years. We therefore recommend that you plan the installation in such a way that this rust separation can run off in a defined manner and that there is no discolouration in the area of the objects.
When combining wooden and corten steel seat covers, the iron oxide adhering to the surface and the tannic acid present in the wood can cause dark grey and black discolouration of the wooden covers. This is a natural process in this combination and does not justify a complaint. With increasing natural greying of the wood, the grey stains that appear in advance disappear and the surface colour converges.
The seat cushions are made of wood. Wood is a natural material that can vary in colour. The seat covers are made exclusively from kiln-dried wood. Despite all care, drying cracks may occur and knots may be visible. These are natural characteristics and do not justify a complaint. Border samples can be matched on request.
Wood care instructions:
All wood used outdoors turns grey within a few months and takes on the typical silvery appearance. It is possible to oil the wood with suitable wood preservative oil so that the greying of the wood is delayed. You can find more information on this on our homepage at www.gartenmetall.de
| Format: | L3000 x W1500 |
|---|---|
| Material: | Corten steel |
| Seat cushions: | Hardwood H65xW65mm |
Login